testtest

ZRO Delta

Belt Fed

Belt Fed

SAINT
Took this back to the range with two mags of 55 grain 223 and two mags of 62 grain green tip. The triggertech i put in it is awesome but it didn't help this piece of junk. These targets were shot at 40 yards and off a sled. put another 120 rounds through it. This thing is either going back to the mothership or i'm tradin it off. if i send it back i am not sending my scope back with it like they want and i'm puttin their crappy trigger back in it.

20250621_104534[1].jpg
20250621_095246[1].jpg
20250621_100736[1].jpg
20250621_101519[1].jpg
20250621_110638[1].jpg
20250621_110648[1].jpg
20250621_110701[1].jpg
 
Belt Fed said:
Took this back to the range with two mags of 55 grain 223 and two mags of 62 grain green tip. The triggertech i put in it is awesome but it didn't help this piece of junk. These targets were shot at 40 yards and off a sled. put another 120 rounds through it. This thing is either going back to the mothership or i'm tradin it off. if i send it back i am not sending my scope back with it like they want and i'm puttin their crappy trigger back in it.

View attachment 86548View attachment 86549View attachment 86550View attachment 86551View attachment 86552View attachment 86553View attachment 86554
Click to expand...
Please buy better ARs for my eventual collection “Dad”. I would like more high end MSRs in the inventory, and don’t want to have to deal with substandard equipment. Thanks, from your “adopted son” 😬😉
 
I took everything off i had on this Piece of junk. even put their old crappy trigger back in it. what's funny it feels better since i took it out and put it back. forgot to mention along with the safety detent spring being crushed and the rear lower pin spring being crushed, i had to make a turn on the mag release catch. it would stick open every time it was pushed. the springs that were crushed were put in wrong. the rear pin came out when i opened it up to oil it. the safety needed two hands to operate it cause they crushed the spring and then stuck it back instead of replacing it. i replaced all the springs. Their QC sucks, too bad cause it's a nice lookin rifle.

20250622_093153[1].jpg
 
Belt Fed said:
I took everything off i had on this Piece of junk. even put their old crappy trigger back in it. what's funny it feels better since i took it out and put it back. forgot to mention along with the safety detent spring being crushed and the rear lower pin spring being crushed, i had to make a turn on the mag release catch. it would stick open every time it was pushed. the springs that were crushed were put in wrong. the rear pin came out when i opened it up to oil it. the safety needed two hands to operate it cause they crushed the spring and then stuck it back instead of replacing it. i replaced all the springs. Their QC sucks, too bad cause it's a nice lookin rifle.

View attachment 86622
Click to expand...
Man, I hope mine doesn’t have those issues. It shows up Tuesday. Im not too worried about replacing springs, although it speaks volumes about their QC, but the accuracy (or lack of) that your’s displayed is alarming.
 
SimonRL said:
Man, I hope mine doesn’t have those issues. It shows up Tuesday. Im not too worried about replacing springs, although it speaks volumes about their QC, but the accuracy (or lack of) that your’s displayed is alarming.
Click to expand...
I'm sure mine is just a fluke. i doubt they could stay in business if every rifle like mine was sold. you probably get a good one. i just hope they don't void my warranty since i put that trigger in.
 
Belt Fed said:
I'm sure mine is just a fluke. i doubt they could stay in business if every rifle like mine was sold. you probably get a good one. i just hope they don't void my warranty since i put that trigger in.
Click to expand...
I watched several videos on it and everyone commented on the gritty trigger, but no one had accuracy issues. I’m sorry yours didn’t work out.

I did get the stock and grip that comes on the Zulu2 and put them on my SBR and I really like them. I had a BCM Gunfighter stock on it but didn’t like how the QD point didn’t actually allow my sling to swivel. That seemed counterintuitive.
 
Belt Fed said:
I took everything off i had on this Piece of junk. even put their old crappy trigger back in it. what's funny it feels better since i took it out and put it back. forgot to mention along with the safety detent spring being crushed and the rear lower pin spring being crushed, i had to make a turn on the mag release catch. it would stick open every time it was pushed. the springs that were crushed were put in wrong. the rear pin came out when i opened it up to oil it. the safety needed two hands to operate it cause they crushed the spring and then stuck it back instead of replacing it. i replaced all the springs. Their QC sucks, too bad cause it's a nice lookin rifle.

View attachment 86622
Click to expand...
Do you need my address?🤣🤣
 
I have been in contact with the owner of this place, and i sent him pics of targets and told him about the other things i had to fix. this is the third e mail from him. he was very apologetic and promised to fix the gun right. he went into detail about their operation and he has been screaming QC at his two builders for months.

I was going to unload this thing but guess i'll give em a chance and send it back. my concern is the same two that built it going to fix it. I'm pretty sure he showed em my e mail. it does sound like they are trying and have excellent customer service. This may be a cheaper AR but it has zero slop between the halves and looks like the parts they use are decent. it was just hurried when put together. no clue what's going on with the accuracy. could be barrel and could be the BCG. i got a box from the gun shop i just hate sending stuff back. but guess i will. cause it's not worth anything with the accuracy it has now.
 
no life said:
Sucks this one had zero QC. I hope the accuracy changes to better and the QC it before sending it back to you...
Click to expand...
Belt Fed said:
I have been in contact with the owner of this place, and i sent him pics of targets and told him about the other things i had to fix. this is the third e mail from him. he was very apologetic and promised to fix the gun right. he went into detail about their operation and he has been screaming QC at his two builders for months.

I was going to unload this thing but guess i'll give em a chance and send it back. my concern is the same two that built it going to fix it. I'm pretty sure he showed em my e mail. it does sound like they are trying and have excellent customer service. This may be a cheaper AR but it has zero slop between the halves and looks like the parts they use are decent. it was just hurried when put together. no clue what's going on with the accuracy. could be barrel and could be the BCG. i got a box from the gun shop i just hate sending stuff back. but guess i will. cause it's not worth anything with the accuracy it has now.
Click to expand...
Give it a week. Me and @KillerFord1977 might be taking a roadtrip to NC to visit their QC guys we’ll get it sorted East End style.

1750740315163.gif
 
You must log in or register to reply here.
Back
Top