testtest

AOS Plate question

rcurtner said:
SimonRL gonna replace SRO on my Operator for a Holosun EPS 6moa green. Do you know what AOS plate is needed for the swap?
Click to expand...
Man, I wish that was a straightforward question. Both the EPS and EPS Carry are the Holosun K (modified RMSc) footprint despite the fact that they are different sizes. The EPS comes with an Holosun K to RMR adapter plate. Springfield says A12B Hex Wasp plate is a Holosun 507k/RMSc plate. If it’s a true RMSc plate you will need to file the rear bosses down to fit the EPS. Perhaps someone else can chime in on that. You will also need M4x10mm screws as the screws that come with the EPS will not fit the plate. You can pick some up here. https://www.battlewerx.com/holosun-scs-320-mounting-screws-m4-x-7-x-10mm-t20-ip20-pair/
 
SimonRL said:
Man, I wish that was a straightforward question. Both the EPS and EPS Carry are the Holosun K (modified RMSc) footprint despite the fact that they are different sizes. The EPS comes with an Holosun K to RMR adapter plate. Springfield says A12B Hex Wasp plate is a Holosun 507k/RMSc plate. If it’s a true RMSc plate you will need to file the rear bosses down to fit the EPS. Perhaps someone else can chime in on that. You will also need M4x10mm screws as the screws that come with the EPS will not fit the plate. You can pick some up here. https://www.battlewerx.com/holosun-scs-320-mounting-screws-m4-x-7-x-10mm-t20-ip20-pair/
Click to expand...
Thanks, will take a look at the 507K & SCS 320.
 
rcurtner said:
Thanks, will take a look at the 507K & SCS 320.
Click to expand...
By the way, I have the EPS and the SCS and I much prefer the EPS. However, most people are under the impression that the EPS and EPS Carry are significantly different in size, but the windows are neglibly different. If you are looking for the size window you would expect with an RMR footprint you may be disappointed.
 
SimonRL said:
By the way, I have the EPS and the SCS and I much prefer the EPS. However, most people are under the impression that the EPS and EPS Carry are significantly different in size, but the windows are neglibly different. If you are looking for the size window you would expect with an RMR footprint you may be disappointed.
Click to expand...
I prefer the EPS, still haven't located the AOS plate for it. Have four pistols with EPS optics really like them.
 
McGanksta said:
@rcurtner is there a picture of this fabled beast, I should have my CDR Operator in a few weeks

Looking to top it with the 507k, not sure on a light yet, but leaning toward the Olight PR3 Valkyrie
Click to expand...
IMG_0669.JPG
 
Going to re-bump this thread.
Picking up the pistol on Friday, and managed to get a A12b plate (RMSc).
The pistol comes with a voucher for another plate for $40, if I recall.

So I am looking for a listing of the widths of the different plates, so I can see how much wider they will be compared to the slide.

Also, willing to take recommendations for a different mounting footprint as well.
I know very little about Red dot optics, this is my crash course in them.

Thank you all in advance

McG
 
TheGeneral39 said:
Hi All. Can anyone confirm if the A12B would fit flush with no overhang on the Springfield Operator? I'm thinking of going with a Holosun 407K as i would like a more streamlined setup. Any advice would be greatly appreciated.
Click to expand...
Used A12B plate to mount an Holosun EPS on my Operator it is flush on both sides of the slide. The EPS has a little over 1/16th overhang on both sides.
 
You must log in or register to reply here.
Back
Top