testtest

Monarch ammo from Academy

I avoid all steel case stuff. It but nature of the harder, less elastic nature of steel has to be harder on a firearm than brass cased. Plus the stuff I’ve seen friends use has been a tad sketchy performance wise. I usually buy new mfg. brass ammo then reload my own.
 
I only buy the brass Monarch stuff. Anything steel case is a pass, ESPECIALLY if it's that lacquer coat ****
 
Follow up:
I’ve shot a good bit of the 9mm and .45 that I recently bought from academy , which initiated my OP question…
Conclusion: there were no malfunctions. Brass seemed fine (I do not buy steel). Accuracy was good (hard for me to gauge, since my shooting doesn’t include very good target stands, I don’t have a rest, and I’m in early stages of arthritis, etc). But…

It is FILTHY. I do not recommend for high end or tight-fitting guns, or for competition.
Be prepared to clean afterwards.
 
Old_Me said:
this one article mentions the dirtiness of the ammo.

for me, even though i clean and lube after every range visit, i'd rather shoot Magtech....

not only that, but in the picture in this article, the brass to me, looks substandard.

proarmory.com

Monarch 9mm Ammo Review: Budget Performance with Eastern European Roots

Looking for affordable 9mm rounds? Monarch delivers cost-effective performance with steel casings and Berdan priming. Is it worth the trade-offs? Dive into this review to see how it stacks up against premium options.
proarmory.com proarmory.com
Click to expand...
At the manufacturing level, monarch is just rebranded magtech. I’ve never had it overly dirty, I have felt it’s cleaner than Federal Champion (which I shot for over a year exclusively). But everyone has their own experiences.
 
td141523 said:
At the manufacturing level, monarch is just rebranded magtech. I’ve never had it overly dirty, I have felt it’s cleaner than Federal Champion (which I shot for over a year exclusively). But everyone has their own experiences.
Click to expand...

They switch manufacturers somewhat often. I've seen their ammo rebranded from PPU, BPS, and Magtech to name a few. Their Steel AK stuff was Barnaul mostly.

I've never had an issue with any of the 9mm, .45ACP, or .223/5.56 so far and i've got 10's of thousands of rounds between those calibers across a bunch of platforms. Dirty, sure. But most cheap range ammo is, regardless of manufacturer.
 
td141523 said:
At the manufacturing level, monarch is just rebranded magtech. I’ve never had it overly dirty, I have felt it’s cleaner than Federal Champion (which I shot for over a year exclusively). But everyone has their own experiences.
Click to expand...
Would not put that junk through any of my guns. My shooting buddy runs Monarch 124 Nato and his guns look like they spent the afternoon at the strip club (brass glitter) , granted, he shoots 3 Caniks. Greasy, glittery mess if you ask me.
 
It's meh at best and inconsistent (with older .308 Win) at worst. It's cheep and it works OK at the range. I won't use it because I don't use that brand of brass for my reloads.
 
I know I'm late to this party, but thought I'd add my 2 cents worth...

I was shooting some Monarch 45 ACP bulk ammo, 230gr FMJ and had a squib that I failed to catch (didn't have a shooting buddy with me that day). The bullet lodged about half way down the barrel. Because I was also experiencing some feeding issues with the ammo, I totally missed the fact that the squib had happened. I cleared the "misfeed" and fired again. Nope, I was VERY lucky and the gun didn't self-disassemble. I attribute that piece of good fortune to the relatively low operating pressure of the 45 ACP and the fact that the Monarch "cheapo range ammo" is probably underpowered. Rather, the shot following the squib ringed the barrel and, of course, the slide was wedged up tightly where the barrel was distended! Lesson learned. Use trusted quality ammo for rapid fire strings. I've still got some of that Monarch ammo and will shoot it up. Slowly. One shot at time. Checking. After. Every. Shot.
 
You must log in or register to reply here.
Back
Top